A film positive is a black-on-clear print you lay on a coated screen and burn with light. Where the film is black, the emulsion stays soft and washes out into your stencil. To get a good one from an inkjet, make the film at exact size, print it at 100% with color management off and density raised, then check it against a light and a ruler.


1. Make the film at the right size
Whatever makes your film, it has to come out at exactly the size you set. Halftoned exports a PDF whose page is the film's exact size, and adds a scale-check ruler (whole inches with quarter-inch ticks) so you can verify it after printing.
2. Set the halftone for your mesh
A common rule of thumb is film LPI of about mesh count divided by 4 to 5. Go finer than your mesh can hold and highlight dots wash out while shadows bridge into solids. You find out after you have burned the screen.
| Mesh | Suggested LPI |
|---|---|
| 110 | 24 |
| 156 | 35 |
| 200 | 44 |
| 230 | 51 |
| 305 | 68 |
These use mesh divided by 4.5, which is the guidance built into Halftoned. See LPI for your mesh, or put your own mesh into the LPI calculator. For a one-color photo, the free halftone generator makes the film at those settings.
3. Load the film the right way
Inkjet film has one coated side that holds the ink. Print on that side: it is the duller of the two, and a damp fingertip sticks to it slightly. Ink on the bare side beads up and never dries.
Most inkjet positives are printed right-reading and positive. Mirror the film, or print a negative, only if your darkroom burns the other way.
4. The three print settings that matter
- Scale: Actual Size, 100%. Never Fit to Page, Shrink to fit or Scale to media. This decides whether the film registers. Check it again after a driver update; some drivers reset it.
- Color management: off. You are printing a black separation, not a photograph. Color management lightens solids.
- Density: raise it. Raise the driver's color density, starting from the printer maker's recipe, and use the film or transparency media setting if the driver has one.
These settings are in the driver dialog on a Mac or Windows computer, which is where films should be printed from. The printer list has the maker's film settings for the models that publish them.
5. Pick the print resolution
Print the film at 720 dpi for crisp dot edges. 360 dpi is enough at 55 LPI and below; a finer screen at 360 dpi does not get enough printer dots per halftone dot to draw a clean edge. Go to 1440 dpi for fine type and rulings over 85 LPI.
6. Let it dry, then check the film
Let the ink dry before you stack the film or lay it on a screen. Wet ink smears and can stick to the emulsion.
Then hold it to a light. The solids should block it. Print a density bar in black-only and in color mode and keep whichever blocks more light. If light still comes through, work through film positive not dark enough. Last, measure the scale ruler with a steel rule, tick to tick.
7. Burn a test
The only real test is a burned screen. Expose a test screen, wash it out, and adjust density and exposure from what the stencil holds. A step wedge tells you the smallest and largest dot your screen keeps: see find your printable dot range.
Try it
Halftoned makes the film in a browser tab. $150 a year or $15 a month, unlimited films. See the preview or the pricing.
Questions
Can any inkjet printer print film positives?
Any printer that can print a PDF at 100% can print the film. What differs is how dense the black is. Pigment printers with a film media setting are the easy case; dye-based printers are the hardest and may need a different black ink or a double strike.
What resolution should I print film positives at?
720 dpi suits most halftones. 360 dpi is enough at 55 LPI and below, and 1440 dpi helps with fine type and rulings over 85 LPI.
Why is my film positive the wrong size?
Almost always the print dialog scaled it. Print at Actual Size or 100%, never Fit to Page. If it is still off by a fraction of a percent at 100%, the printer's paper feed is drifting, and a scale target measured with a steel rule gives you the correction.
Do I need special film?
Yes. Use a film made for inkjet positives. Its coating holds more ink than a generic transparency, so the black is denser and dries instead of pooling.